DIS module testing

The Ignition Module is tasked with activating the two Ignition Coil Packs that feed the 8 Spark Plugs that the 2.3L 4 Cylinder Engine is equipped with.

Full procedure

Here's the basics that you need to get to the bottom of the problem. In a nutshell, this is what happens when you turn On the Key and crank the Engine:

The Crank Sensor is fed with Power and Ground.
The Crank Sensor is a Hall-Effect type Sensor.
The Crankshaft rotation induces the Crank Sensor to start creating two separate Crank Signals.
One Crank Signal is called the CKP (Crankshaft Position) Signal.
The CKP Signal is only sent to the ICM.
The other Crank Signal is called the CDI (Cylinder Identification) Signal.
The CID (Cylinder Identification) Signal is the one that helps the Ignition Control Module synchronize the Ignition Coil Packs so that they fire in the correct Firing Order.
Both the ICM and the PCM receive the CID Signal.
The Ignition Module now starts to activate the Coil Packs.
During Engine Cranking, only the Right Side Spark Plugs (Exhaust Manifold Side of the Engine) are fired.
Once the Engine starts, the PCM now commands the ICM to fire both Coil Packs through the Dual Plug Inhibit (DPI) circuit (circuit 6 of the ICM Top Connector), .
Each Coil Pack feeds Spark to 4 Spark Plugs on either side of the Engine.
Spark Plugs on the Intake Manifold Side of the Engine are referred to as: Intake Side Spark Plugs or Right Side Spark Plugs.
Spark Plugs on the Exhaust Manifold Side of the Engine are referred to as: Exhaust Side Spark Plugs or Left Side Spark Plugs.

1991 2WD Ranger and F150 ball joint replacement steps

Time for some new ball joints and suspension parts.  The Ranger starting pitching when I drove over uneven payments or lines in the payment.  An inspection reveled one bad upper ball joint.  Since all the other parts have to come off and I don't as a rule reuse a part once I have taken it off, new parts are in order.

Ball joints:
REMOVE THE SPINDLE
Raise the truck, support the truck using jack stands and chok rear wheels.

F150 simular design

1. A ford 150 has the same design as the ranger, here is a video on it.
http://www.realfixesrealfast.com/realfixesrealfast.com/Steering_%26_Suspension/Pages/Ford_F150_Ball_Joint.html
2. Using a clamp, remove the pressure the brake pads exert on the rotor. Remove the brake caliper and tie/support it.
3. Remove the tie rod end from the spindle. Do not take the nut completely off, this will protect the threads (from hammer blows) should you reuse it. Use a hammer hitting the ring. Put the nut on the tie rod end before you lose it. Don't reuse any cotter pin.
4. Take the cotter pin and nut off the lower ball joint. If the cotter pin is stuck, break off the "legs" by wiggling them in their hole. Soak with penatrating oil like PB Blaster. The nut size is a 24mm socket. Do not take the nut completely off, this will protect the threads (from hammer blows) should you reuse it and will prevent it from dropping off/out of the I-beam when the upper joint is free.
2. The upper ball joint is held in place with a pinch/clamp bolt. Clean away the rust and dirt out of the slot in the middle. Soak the shit out of it with penatrating oil like PB Blaster, then take that bolt out. NOTE: Tap the bolt with a hammer to help free it (don't over do this or you will mushroom the bolt head), some LIGHT heat may also be helpful.
3. Your ranger has a camber adjuster (factory is preset) on the top of the I-beam to adjust the camber when the vehicle is aligned. It is trapped by the pinch bolt. Make a note where the camber adjuster was position, so that if it's adjustable you can put it back in the same place, or your alignment will be changed. You have to pry the adjuster out, soak with penatrating oil. Use a rod seperator or an open ended wrench to pry it up. Clean/polish it before reinsertion.
8. There isn't much holding the spindle in place now. You have to hit the bottom ring of the I-beam to free the lower ball joint. If you strike the eye with your hammer, it should break loose (see graphic).
9. When it releases, the heavy spindle will pop down, held in place by the nut. Remove the nut, remove the spindle.

TIP1: Check the brake line.  If damaged, now is good time to replace it.
TIP2: Check all front end joints for replacement.  These parts are fairly cheap online.

Replacing the 1991 2WD Ranger ball joints:
1. Borrow the special ball joint press from the auto parts store ("C-frame assembly tool") to press the new ball joints in or out.

2. Remove any old grease fittings and rubber boots. The upper ball joint has a snap-ring on it. Spray the ball joint with the PB blaster both sides and the sanp ring. Hit the end of the end of the snap ring with a chisel or screwdriver to break it free from the rust, then used needle nosed pliers or a screwdriver to spread the snap ring enough to work it up out of the slot. Snap ring pliers also work.

3. The lower ball joint doesn't have a snap ring. It has a lip on the top of it (inside part of spindle) to keep the ball joint from going down through the hole. The lower ball joint can only be removed in one direction. The lower ball joint has to be pressed UP or tapped/beat up to remove it! Hit it with the PB blaster both sides. Prior to installing the replacement ball joints, clean the wheel spindel ball joint bores thoroughly, remove any burrs, grease bores with finger.

4. The upper ball joint should be installed first. Using the C-frame and ball joint installer, press the upper ball joint into place. Install a new snap ring into the groove at the bottom of the ball joint.

5. Using the C-frame and ball joint installer, press-in the lower ball joint.

6. And install the grease fittings. Install the wheel spindle. Grease the ball joints.

7. When you put everything back together, I'd check the pins and rails that the brake calipers slide on. They often don't slide very well because they get rusty.